Permanent Lifeline System

A Permanent horizontal lifeline System is typically a cable that is installed parallel to a fall hazard. Properly connecting to a horizontal lifeline with a lanyard and harness enables the user to travel parallel to the fall hazard. The lifeline is usually attached to the structure at set intervals, and can often change direction to follow the profile of the roof edge or other fall hazards. Horizontal lifelines can be attached at foot level when working on a top-level surface, such as a roof, but can also be attached overhead, such as airline hangers and bus depots.

A Horizontal Lifeline (HLL) system is required when a worker needs to traverse an area at height, such as a narrow roof area near the roof edge or along a sloped roof, while still connected and protected by a Fall Protection System. The design of the HLL is a complex process as loads are applied differently than from a single anchorage point.
Flexible horizontal lifeline systems (HLL) are for the attachment of personal protective equipment (PPE) for protection against falls from height.

These systems are used for fall arresting and may be used for work positioning and travel restriction (worker restraint). Lifeline System in the form of fall protection that involves the safe stopping of a person already falling. It is one of several forms of fall protection which also include fall prevention (general protection that prevents persons from entering a fall hazard area e.g., guard rails) and fall restraint (personal protection which prevents persons who are in a fall hazard area from falling, e.g., fall restraint lanyards).

SecuRope - On Roof

For 4 users
12m max. between fixations
Freehand system
Undeformable
Energy absorbing on orientable intermediate anchors
Wide range of brackets for all structures
Possibility of custom-made solutions with the Fallprotec’s engineering department

EN 795:2012 Type C
CEN/TS 16415:2013
AINSI Z359
CSA Z259

Industrial
Housing
Buildings
Fall arrest
Work in restraint

SecuRope - Overhead

Most used configuration for industrial halls as the overhead lifeline reduces the fall distance.

For 4 users
Undeformable
Can be used with retractable fall arresters
Also for curved sections (minimum radius: 300mm)
The glider passes smoothly over NEO anchor with retractable fall arrester
Often used in the industry for works above machines, recommended for a distance between the lifeline and walkway up to 7m
Can be installed in corrosive environments.

EN 795:2012 Type C
CEN/TS 16415:2013
AINSI Z359
CSA Z259

Industrial
Housing
Buildings
Fall arrest
Work in restraint

Securope – Bespoke Solutions

Bespoke solutions for particular field requirements can be provided by TSS & Fallprotec team.

Type of fixation - On post

The user stays connected while moving along the lifeline and passing the intermediate anchors, having excellent freedom of movement and reaching safely any point of the structure. For rigid structures such as concrete or steel beams, the undeformable TSS post is a safe choice.

For 2 users
Undeformable
Compatible with Securope EVO, Securope 2012, Securail and Securail Pro
Galvanized steel
Stainless steel on demand
Upon request, options for bespoke fixations

EN 795:2012 Type C and D
CEN/TS 16415:2013
AINSI Z359
CSA Z259

Industrial
Housing
Buildings
Fall arrest
Work in restraint

Type of fixation - On Unipost

Unipost means « Universal post ». It may be installed on several types of roofing, hot deck, cold deck, wood deck, prefabricated slab, and concrete slab, thanks to the universal fixing interface in the laser-cut plate. The Unipost protects the roofing from possible damages, when stopping a fall, thanks to an energy-absorbing device located at the foot of the post, only the post tube deforms and not the fixing interface.

For 2 users
Deformable
Compatible with Securope EVO, Securope and Secura
Usable on various roof types (concrete, hollow concrete, cold deck, hot deck, wooden roof)
Energy absorbing
Can be mounted before the isolation to secure the construction site
Easy to mount on trapezoidal metal sheet thanks to its self-drilling screws

EN 795:2012 Type C
CEN/TS 16415:2013
AINSI Z359
CSA Z259

Industrial
Housing
Buildings
Fall arrest
Work in restraint

Type of fixation - On Cold Deck Brackets

The fixing bracket for cold deck roofs has a unique design that distributes the load evenly. Combined with the energy-absorbing mechanism of the SecuRope NEO lifeline, it is the best system for fragile roofs. Supplied with self-drilling screws specially designed for their high pull-out strength. Ideal for the maintenance and repair of any industrial facility, safe access to solar panels, ventilation outlets, roof skylights, and gutters.

For 4 users
Energy absorbing
Absorbs dilation and contraction of roof sheets
Compatible with Securope, Securail and Securail Pro

EN 795:2012 Type C
CEN/TS 16415:2013
AINSI Z359
CSA Z259

Industrial
Fall arrest
Work in restraint

Type of fixation - On Standing Seam Roof

The fixing bracket for the standing seam roof is clamped on the seam and doesn’t require any perforation. The clamps combine high pull-out and shear strength. Combined with the SecuRope NEO lifeline, the system completely absorbs the dilatation and contraction of the standing seam roof. Easy to install on new constructions or existing buildings.

For 4 users
Energy and dilatation absorbing
No drilling needed
Wide range of clamps for seams
Aluminium and stainless steel components
Also for copper
Compatible with Securope, Securail and Securail Pro

EN 795:2012 Type C
CEN/TS 16415:2013
AINSI Z359
CSA Z259

Industrial
Housing
Buildings
Fall arrest
Work in restraint

Type of fixation - On Hot Deck Brackets

The Multipost and SpotAnchor are designed for hot-deck roofs. High resistance toggle bolts enable the fixation on corrugated metal sheets, wooden panels, or precast concrete. Only the toggle bolts pass through the isolation, then thermal bridges are minimized. The roofing collar, in bitumen or PVC-P, is pre-fitted in the factory to guarantee waterproofness. Easier to retrofit existing buildings.

For 4 users
Undeformable
Energy absorbing
Can be retrofitted
Compatible with all bituminous structures
Compatible with most EPDM
Reinforced toggle bolt
Available with bituminous or PVC-P membranes
Compatible with Securope 2012, Securail and Securail Pro

EN 795:2012 Type C and D
CEN/TS 16415:2013
AINSI Z359
CSA Z259

Industrial
Housing
Buildings
Fall arrest
Work in restraint

Type of fixation - On Steel Beams

The NEO SecuRope lifeline can be attached to beams through a system of clamps. Using this type of fastening enables a solid fixation of the lifeline without drilling. Particularly useful for industrial configurations, the SecuRope NEO lifeline with crimping rings can stop a fall with very low cable deflection.

For 4 users
Undeformable
Easy and quick installation
Smooth movements along the lifeline
Stainless steel
Harmonized design for standard beams with a flange from 50 to 300mm
Clamping perpendicularly or in parallel to the axis of the exerted force
Compatible with SecuRope, SecuRope EVO, Secura, SecuRail SecuRail Pro and SafeAccess

EN 795:2012 Type C
CEN/TS 16415:2013
AINSI Z359
CSA Z259

Industrial
Fall arrest
Work in restraint

SecuRail Lifeline Classic

Horizontal SecuRail lifeline on ground

The SecuRail is a rigid fall arrest rail that can be installed on ground, wall, and ceiling configurations. Its rectangular shape integrates well with the aesthetics of buildings. The cross-shaped junction absorbs the dilatation as a result of temperature variation. A variety of 6 fall arrest trolleys makes this rail highly versatile. The openable trolley VIA 6 enables the end-user to connect and disconnect the trolley at any point of the rail.

For 2 users
Anodized Aluminium
1, 4 kg/m
Low deflection
Absorbs dilatation and contraction of roof sheets
Possibility of custom-made solutions with the TSS engineering department

EN 795:2012 Type D
CEN/TS 16415:2013
AINSI Z359
CSA Z259

Industrial
Housing
Buildings
Fall arrest
Work in restraint
Vertical structures

SecuRail Pro

Horizontal SecuRail 2016 lifeline on ground

The SecuRail 2016 is a rigid and versatile fall arrest rail. This unique profile has high inertia that enables a 6-meter span between supports. lt is ideal for work sites with low fall clearance.

For 2 users
Anodized Aluminium
1, 4 kg/m
Span up to 6m
Low deflection
Absorbs dilatation / contraction
Possibility of custom-made solutions with the TSS engineering department

EN 795:2012 Type D
CEN/TS 16415:2013
AINSI Z359
CSA Z259

Industrial
Housing
Buildings
Fall arrest
Work in restraint
Rope access
Over trucks

SafeAccess Rail Fall Arrest

Horizontal fall arrest

The SafeAccess is an undeformable fall arrest rail for industrial applications. Installed in overhead configuration, it is the most suitable system when the fall clearance is low. ATEX certified for potentially explosive atmospheres, this rail is also ideal for petrochemical industries. The aluminum rail is protected by a high-quality powder-coated surface treatment that resists the marine environment. The NAV 2 trolley equipped with rollers follows smoothly without any action from the end-user.

For 4 users
For 2 users with Flexbow system
Anodized Aluminum
5 kg/m
Span up to 6m
Undeformable
ATEX Certified
Aluminum 6060T6
Possibility to fold away the Flexbow and SafeAccess system when not in use
Possibility to fold away the Flexbow and SafeAccess system when not in use

EN 795:2012 Type D
CEN/TS 16415:2013
AINSI Z359
CSA Z259

Industrial
Fall arrest
Over trucks

SecureRope QuickSet Cable Lifeline

SecuRope QuickSet Vertical lifeline

The SecuRope QuickSet is designed for wind turbines, pylones, masts or industrial sites. This flexible system is used with stainless steel cables. The glider is openable and can be inserted or removed at any point of the cable.

Two types of fall arrest systems are possible with this lifeline.

Type 1: Energy absorber fixed on the top anchor. It is permanently fixed on the lifeline.

Type 2: Energy absorber fixed on the opening glider. The glider locks instantly in case of a fall, triggering the energy absorption device.

SecuRail Pro MastLadder

SecuRail MastLadder and SecuRail Pro Vertical 2016 lifeline clamped on a ladder

The SecuRail Pro Vertical is a rigid lifeline to secure access on any structure. When clamped on an existing ladder it secures the end user much better than the regular safety hoops.

A MastLadder fitted with fixed rungs is designed for confined spaces, for industrial halls or for telecommunication towers. Undeformable stainless steel brackets connect the MastLadder to the structure.

SafeLadder Pro

The SafeLadder works with the same rail system as the MastLadder.

A Securail Pro is integrated to the frame of a ladder. A GRANVIA 4 trolley is inserted on this frame, which means that the user can comfortably climb the ladder up while being secured at all times.

Various SafeLadder types and accessories are available to fit any situation:
temporary SafeLadder, platform to cross the parapet, fold-up section for confined spaces, telescopic SafeLadder and traversing SafeLadder along a SafeAccess rail.

This ladder type is much safer than traditional safety hoop ladders. A foot rest is installed every 10m